Linux version 2.6.17-rc2-pa4 (varenet@Esperanza.r3z0) (gcc version 4.0.3 (Debian 4.0.3-1)) #1 SMP Sun Apr 23 01:08:22 CEST 2006 FP[0] enabled: Rev 1 Model 16 The 32-bit Kernel has started... Initialized PDC Console for debugging. Determining PDC firmware type: System Map. model 00005d40 00000491 00000000 00000002 77ec06ff 100000f0 00000008 000000b2 000000b2 vers 00000301 CPUID vers 17 rev 11 (0x0000022b) capabilities 0x3 model 9000/785/J6000 Memory truncated to 3584 MB Total Memory: 3584 MB On node 0 totalpages: 917504 DMA zone: 917504 pages, LIFO batch:31 LCD display at f05d0008,f05d0000 registered SMP: bootstrap CPU ID is 0 Built 1 zonelists Kernel command line: root=/dev/sda3 HOME=/ console=ttyS0 TERM=vt102 palo_kernel=2/vmlinux-cvs PID hash table entries: 4096 (order: 12, 16384 bytes) Console: colour dummy device 160x64 Dentry cache hash table entries: 524288 (order: 9, 2097152 bytes) Inode-cache hash table entries: 262144 (order: 8, 1048576 bytes) Memory: 3670016k available Calibrating delay loop... 1097.72 BogoMIPS (lpj=548864) Mount-cache hash table entries: 512 Brought up 1 CPUs migration_cost=0 NET: Registered protocol family 16 Searching for devices... Found devices: 1. Astro BC Runway Port at 0xfed00000 [10] { 12, 0x0, 0x582, 0x0000b } 2. Elroy PCI Bridge at 0xfed30000 [10/0] { 13, 0x0, 0x782, 0x0000a } 3. Elroy PCI Bridge at 0xfed34000 [10/2] { 13, 0x0, 0x782, 0x0000a } 4. Elroy PCI Bridge at 0xfed38000 [10/4] { 13, 0x0, 0x782, 0x0000a } 5. Elroy PCI Bridge at 0xfed3c000 [10/6] { 13, 0x0, 0x782, 0x0000a } 6. Duet W+ at 0xfffa0000 [32] { 0, 0x0, 0x5d4, 0x00004 } 7. Duet W+ at 0xfffa2000 [34] { 0, 0x0, 0x5d4, 0x00004 } 8. Memory at 0xfed10200 [49] { 1, 0x0, 0x00a, 0x00009 } Releasing cpu 1 now, hpa=fffa2000 FP[1] enabled: Rev 1 Model 16 migration_cost=2000 CPU(s): 2 x PA8600 (PCX-W+) at 552.000000 MHz Whole cache flush 175123 cycles, flushing 4935680 bytes 742768 cycles Setting cache flush threshold to 5c0 (2 CPUs online) SBA found Astro 2.1 at 0xfed00000 LBA version TR4.0 (0x5) found at 0xfed30000 PCI: Scanning bus 0000:00 PCI: Found 0000:00:0c.0 [1011/0019] 000200 00 PCI: Calling quirk 103105c0 for 0000:00:0c.0 PCI: Found 0000:00:0d.0 [11d4/1889] 000401 00 PCI: Calling quirk 103105c0 for 0000:00:0d.0 PCI: Found 0000:00:0e.0 [100b/0002] 000101 00 PCI: Calling quirk 1031ac4c for 0000:00:0e.0 PCI: Enabled native mode for NS87415 (pif=0x8f) PCI: Calling quirk 103105c0 for 0000:00:0e.0 PCI: Found 0000:00:0e.1 [100b/000e] 000680 00 PCI: Calling quirk 103105c0 for 0000:00:0e.1 PCI: Found 0000:00:0e.2 [100b/0012] 000c03 00 PCI: Calling quirk 103105c0 for 0000:00:0e.2 PCI: Found 0000:00:0f.0 [1000/000b] 000100 00 PCI: Calling quirk 103105c0 for 0000:00:0f.0 PCI: Found 0000:00:0f.1 [1000/000b] 000100 00 PCI: Calling quirk 103105c0 for 0000:00:0f.1 PCI: Fixups for bus 0000:00 PCI: Bus scan for 0000:00 returning with max=00 LBA version TR4.0 (0x5) found at 0xfed34000 PCI: Scanning bus 0000:01 PCI: Found 0000:01:01.0 [8086/b154] 000604 01 PCI: Calling quirk 103105c0 for 0000:01:01.0 PCI: Fixups for bus 0000:01 PCI: Scanning behind PCI bridge 0000:01:01.0, config 020201, pass 0 PCI: Scanning behind PCI bridge 0000:01:01.0, config 000000, pass 1 PCI: Scanning bus 0000:02 PCI: Found 0000:02:04.0 [1000/000b] 000100 00 PCI: Calling quirk 103105c0 for 0000:02:04.0 PCI: Found 0000:02:04.1 [1000/000b] 000100 00 PCI: Calling quirk 103105c0 for 0000:02:04.1 PCI: Found 0000:02:06.0 [1011/0019] 000200 00 PCI: Calling quirk 103105c0 for 0000:02:06.0 PCI: Found 0000:02:07.0 [1011/0019] 000200 00 PCI: Calling quirk 103105c0 for 0000:02:07.0 PCI: Fixups for bus 0000:02 PCI: Bus scan for 0000:02 returning with max=02 PCI: Bus scan for 0000:01 returning with max=02 LBA version TR4.0 (0x5) found at 0xfed38000 PCI: Scanning bus 0000:03 PCI: Found 0000:03:02.0 [1011/0019] 000200 00 PCI: Calling quirk 103105c0 for 0000:03:02.0 PCI: Fixups for bus 0000:03 PCI: Bus scan for 0000:03 returning with max=03 LBA version TR4.0 (0x5) found at 0xfed3c000 PCI: Scanning bus 0000:04 PCI: Found 0000:04:03.0 [12ae/0001] 000200 00 PCI: Calling quirk 103105c0 for 0000:04:03.0 PCI: Fixups for bus 0000:04 PCI: Bus scan for 0000:04 returning with max=04 Generic PHY: Registered new driver SCSI subsystem initialized unwind_init: start = 0x104a5320, end = 0x104cf7f0, entries = 10829 JFS: nTxBlock = 8192, nTxLock = 65536 SGI XFS with no debug enabled io scheduler noop registered io scheduler anticipatory registered (default) PCI: Calling quirk 1030fe40 for 0000:00:0c.0 PCI: Calling quirk 1037a3c8 for 0000:00:0c.0 PCI: Calling quirk 1030fe40 for 0000:00:0d.0 PCI: Calling quirk 1037a3c8 for 0000:00:0d.0 PCI: Calling quirk 1030fe40 for 0000:00:0e.0 PCI: Calling quirk 1037a3c8 for 0000:00:0e.0 PCI: Calling quirk 1030fe40 for 0000:00:0e.1 PCI: Calling quirk 1031ade0 for 0000:00:0e.1 SuperIO: Found NS87560 Legacy I/O device at 0000:00:0e.1 (IRQ 68) SuperIO: Serial port 1 at 0x3f8 SuperIO: Serial port 2 at 0x2f8 SuperIO: Parallel port at 0x378 SuperIO: Floppy controller at 0x3f0 SuperIO: ACPI at 0x7e0 SuperIO: USB regulator enabled PCI: Calling quirk 1037a3c8 for 0000:00:0e.1 PCI: Calling quirk 1030fe40 for 0000:00:0e.2 PCI: Calling quirk 1037a3c8 for 0000:00:0e.2 PCI: Calling quirk 1030fe40 for 0000:00:0f.0 PCI: Calling quirk 1037a3c8 for 0000:00:0f.0 PCI: Calling quirk 1030fe40 for 0000:00:0f.1 PCI: Calling quirk 1037a3c8 for 0000:00:0f.1 PCI: Calling quirk 1030fe40 for 0000:01:01.0 PCI: Calling quirk 1037a3c8 for 0000:01:01.0 PCI: Calling quirk 1030fe40 for 0000:02:04.0 PCI: Calling quirk 1037a3c8 for 0000:02:04.0 PCI: Calling quirk 1030fe40 for 0000:02:04.1 PCI: Calling quirk 1037a3c8 for 0000:02:04.1 PCI: Calling quirk 1030fe40 for 0000:02:06.0 PCI: Calling quirk 1037a3c8 for 0000:02:06.0 PCI: Calling quirk 1030fe40 for 0000:02:07.0 PCI: Calling quirk 1037a3c8 for 0000:02:07.0 PCI: Calling quirk 1030fe40 for 0000:03:02.0 PCI: Calling quirk 1037a3c8 for 0000:03:02.0 PCI: Calling quirk 1030fe40 for 0000:04:03.0 PCI: Calling quirk 1037a3c8 for 0000:04:03.0 Soft power switch enabled, polling @ 0xf0400804. Generic RTC Driver v1.07 Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled serial8250: ttyS0 at I/O 0x3f8 (irq = 3) is a 16550A serial8250: ttyS1 at I/O 0x2f8 (irq = 4) is a 16550A Linux Tulip driver version 1.1.13-NAPI (December 15, 2004) tulip0: no phy info, aborting mtable build tulip0: MII transceiver #1 config 1000 status 782d advertising 01e1. eth0: Digital DS21142/DS21143 Tulip rev 65 at 004f2000, 00:10:83:FF:27:6B, IRQ 66. tulip1: EEPROM default media type Autosense. tulip1: Index #0 - Media MII (#11) described by a 21142 MII PHY (3) block. tulip1: MII transceiver #0 config 1000 status 7809 advertising 01e1. eth1: Digital DS21142/DS21143 Tulip rev 65 at 004f4000, 00:30:6E:2D:77:56, IRQ 72. tulip2: EEPROM default media type Autosense. tulip2: Index #0 - Media MII (#11) described by a 21142 MII PHY (3) block. tulip2: MII transceiver #0 config 1000 status 7809 advertising 01e1. eth2: Digital DS21142/DS21143 Tulip rev 65 at 004f6000, 00:30:6E:2D:77:57, IRQ 73. tulip3: EEPROM default media type Autosense. tulip3: Index #0 - Media MII (#11) described by a 21142 MII PHY (3) block. tulip3: MII transceiver #1 config 3100 status 7849 advertising 0101. tulip3: Advertising 01e1 on PHY 1, previously advertising 0101. eth3: Digital DS21142/DS21143 Tulip rev 65 at 004f8000, 00:10:83:F6:3E:C2, IRQ 74. sym0: <896> rev 0x4 at pci 0000:00:0f.0 irq 69 sym0: PA-RISC Firmware, ID 7, Fast-40, LVD, parity checking sym0: SCSI BUS has been reset. scsi0 : sym-2.2.3 sym1: <896> rev 0x4 at pci 0000:00:0f.1 irq 69 sym1: PA-RISC Firmware, ID 7, Fast-40, LVD, parity checking sym1: SCSI BUS has been reset. scsi1 : sym-2.2.3 Vendor: SEAGATE Model: ST336704LC Rev: HP00 Type: Direct-Access ANSI SCSI revision: 03 target1:0:5: tagged command queuing enabled, command queue depth 16. target1:0:5: Beginning Domain Validation target1:0:5: asynchronous target1:0:5: wide asynchronous target1:0:5: FAST-40 WIDE SCSI 80.0 MB/s ST (25 ns, offset 31) target1:0:5: Domain Validation skipping write tests target1:0:5: Ending Domain Validation PCI: resource not parented! [4000-4fff] PCI: resource not parented! [f5000000-f50fffff] sym2: <896> rev 0x7 at pci 0000:02:04.0 irq 70 sym2: PA-RISC Firmware, ID 7, Fast-40, LVD, parity checking sym2: SCSI BUS has been reset. scsi2 : sym-2.2.3 sym3: <896> rev 0x7 at pci 0000:02:04.1 irq 71 sym3: PA-RISC Firmware, ID 7, Fast-40, LVD, parity checking sym3: SCSI BUS has been reset. scsi3 : sym-2.2.3 SCSI device sda: 71132960 512-byte hdwr sectors (36420 MB) sda: Write Protect is off sda: Mode Sense: 9f 00 10 08 SCSI device sda: drive cache: write back w/ FUA SCSI device sda: 71132960 512-byte hdwr sectors (36420 MB) sda: Write Protect is off sda: Mode Sense: 9f 00 10 08 SCSI device sda: drive cache: write back w/ FUA sda: sda1 sda2 sda3 sda4 sd 1:0:5:0: Attached scsi disk sda sd 1:0:5:0: Attached scsi generic sg0 type 0 HP SDC: No SDC found. mice: PS/2 mouse device common for all mice Advanced Linux Sound Architecture Driver Version 1.0.11rc4 (Wed Mar 22 10:27:24 2006 UTC). [snd_ad1889_ac97_ready] ready after 352 ms ac97 quirk for AD1889 (11d4:1889) ALSA device list: #0: Analog Devices AD1889 at 0xf400c000 irq 67 oprofile: using timer interrupt. NET: Registered protocol family 2 IP route cache hash table entries: 131072 (order: 7, 524288 bytes) TCP established hash table entries: 262144 (order: 9, 3145728 bytes) TCP bind hash table entries: 65536 (order: 7, 524288 bytes) TCP: Hash tables configured (established 262144 bind 65536) TCP reno registered TCP bic registered NET: Registered protocol family 1 NET: Registered protocol family 17 XFS mounting filesystem sda3 Ending clean XFS mount for filesystem: sda3 VFS: Mounted root (xfs filesystem) readonly. Freeing unused kernel memory: BUG: warning at arch/parisc/kernel/smp.c:348/smp_call_function() Backtrace: [<10114580>] smp_call_function+0x2ec/0x320 [<101360dc>] on_each_cpu+0x1c/0x50 [<10106498>] free_initmem+0x58/0x1c0 [<10105cdc>] init+0x330/0x3dc [<1010bc5c>] ret_from_kernel_thread+0x1c/0x24 212k freed eth0: Setting full-duplex based on MII#1 link partner capability of 45e1.