Linux version 2.6.12-1-parisc-smp (buildd@sarti) (gcc version 4.0.2 (Debian 4.0.1-9)) #1 SMP Tue Sep 27 11:09:02 UTC 2005
FP[0] enabled: Rev 1 Model 16
The 32-bit Kernel has started...
Initialized PDC Console for debugging.
Determining PDC firmware type: System Map.
model 00005bd0 00000491 00000000 00000002 779eb6b7 100000f0 00000008 000000b2 000000b2
vers  00000203
CPUID vers 17 rev 7 (0x00000227)
capabilities 0x3
model 9000/785/J5000
Total Memory: 2048 MB
initrd: 4fe0d000-4ffee000
initrd: reserving 3fe0d000-3ffee000 (mem_max 80000000)
On node 0 totalpages: 524288
  DMA zone: 524288 pages, LIFO batch:31
  Normal zone: 0 pages, LIFO batch:1
  HighMem zone: 0 pages, LIFO batch:1
LCD display at f05d0008,f05d0000 registered
SMP: bootstrap CPU ID is 0
Built 1 zonelists
Kernel command line: root=/dev/sda5 console=tty0 sti=10/6/7/0 sti_font=VGA8x16 TERM=linux palo_kernel=4/vmlinux.old
PID hash table entries: 4096 (order: 12, 65536 bytes)
Console: colour dummy device 160x64
Dentry cache hash table entries: 524288 (order: 9, 2097152 bytes)
Inode-cache hash table entries: 262144 (order: 8, 1048576 bytes)
Memory: 2097152k available
Calibrating delay loop... 878.18 BogoMIPS (lpj=4390912)
Security Framework v1.0.0 initialized
Capability LSM initialized
Mount-cache hash table entries: 512
Brought up 1 CPUs
CPU0 attaching sched-domain:
 domain 0: span 00000001
  groups: 00000001
checking if image is initramfs...it isn't (bad gzip magic numbers); looks like an initrd
NET: Registered protocol family 16
EISA bus registered
Searching for devices...
Found devices:
1. Astro BC Runway Port at 0xfed00000 [10] { 12, 0x0, 0x582, 0x0000b }
2. Elroy PCI Bridge at 0xfed30000 [10/0] { 13, 0x0, 0x782, 0x0000a }
3. Elroy PCI Bridge at 0xfed32000 [10/1] { 13, 0x0, 0x782, 0x0000a }
4. Elroy PCI Bridge at 0xfed34000 [10/2] { 13, 0x0, 0x782, 0x0000a }
5. Elroy PCI Bridge at 0xfed38000 [10/4] { 13, 0x0, 0x782, 0x0000a }
6. Elroy PCI Bridge at 0xfed3c000 [10/6] { 13, 0x0, 0x782, 0x0000a }
7. Forte W 2-way at 0xfffa0000 [32] { 0, 0x0, 0x5bd, 0x00004 }
8. Forte W 2-way at 0xfffa2000 [34] { 0, 0x0, 0x5bd, 0x00004 }
9. Memory at 0xfed10200 [49] { 1, 0x0, 0x088, 0x00009 }
CPU0 attaching sched-domain:
 domain 0: does not load-balance
Releasing cpu 1 now, hpa=fffa2000
FP[1] enabled: Rev 1 Model 16
CPU0 attaching sched-domain:
 domain 0: span 00000003
  groups: 00000001 00000002
CPU1 attaching sched-domain:
 domain 0: span 00000003
  groups: 00000002 00000001
CPU(s): 2 x PA8500 (PCX-W) at 440.000000 MHz
Whole cache flush 255012 cycles, flushing 273571852 bytes 36198077 cycles
Setting cache flush threshold to 20 (2 CPUs online)
SBA found Astro 2.1 at 0xfed00000
LBA version TR2.1 (0x2) found at 0xfed30000
PCI: Enabled native mode for NS87415 (pif=0x8f)
LBA version TR2.1 (0x2) found at 0xfed32000
LBA version TR2.1 (0x2) found at 0xfed34000
LBA version TR2.1 (0x2) found at 0xfed38000
LBA version TR2.1 (0x2) found at 0xfed3c000
iosapic: hpa not registered for 0000:06:07.0
SCSI subsystem initialized
TC classifier action (bugs to netdev@vger.kernel.org cc hadi@cyberus.ca)
unwind_init: start = 0x10399aa0, end = 0x103b99a0, entries = 8176
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
Initializing Cryptographic API
SuperIO: Found NS87560 Legacy I/O device at 0000:00:0e.1 (IRQ 68) 
SuperIO: Serial port 1 at 0x3f8
SuperIO: Serial port 2 at 0x2f8
SuperIO: Parallel port at 0x378
SuperIO: Floppy controller at 0x3f0
SuperIO: ACPI at 0x7e0
SuperIO: USB regulator enabled
PDC Stable Storage facility v0.09
Soft power switch enabled, polling @ 0xf0400804.
STI GSC/PCI core graphics driver Version 0.9a
STI PCI graphic ROM found at f7000000 (64 kB), fb at fa000000 (32 MB)
    id 2d08c0a7-9a02587, conforms to spec rev. 8.0a
    graphics card name: PCI_GRAFFITIX1600
sticon: Initializing STI text console.
Console: switching to colour STI console 200x75
Console: switching to colour frame buffer device 200x75
fb0: stifb 1600x1200-8 frame buffer device, PCI_GRAFFITIX1600, id: 2d08c0a7, mmio: 0xfa100000
Generic RTC Driver v1.07
Serial: 8250/16550 driver $Revision: 1.90 $ 13 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 3) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 4) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
mice: PS/2 mouse device common for all mice
NET: Registered protocol family 2
IP: routing cache hash table of 4096 buckets, 96Kbytes
TCP established hash table entries: 131072 (order: 9, 3145728 bytes)
TCP bind hash table entries: 65536 (order: 8, 1310720 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
NET: Registered protocol family 1
NET: Registered protocol family 17
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 1924KiB [1 disk] into ram disk... |/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|done.
VFS: Mounted root (cramfs filesystem) readonly.
Freeing unused kernel memory: Badness in smp_call_function at arch/parisc/kernel/smp.c:340
Backtrace:
 [<101166ec>] smp_call_function+0x31c/0x324
 [<10106b58>] flush_data_cache+0x24/0x40
 [<10105fd8>] free_initmem+0x60/0x1e4
 [<101053c4>] init+0x638/0x674
 [<1010dc5c>] ret_from_kernel_thread+0x1c/0x24

348k freed
sym0: <896> rev 0x4 at pci 0000:00:0f.0 irq 69
sym0: PA-RISC Firmware, ID 7, Fast-40, SE, parity checking
sym0: SCSI BUS has been reset.
sym0: SCSI BUS mode change from SE to SE.
scsi0 : sym-2.2.1
sym0: SCSI BUS has been reset.
sym1: <896> rev 0x4 at pci 0000:00:0f.1 irq 69
sym1: PA-RISC Firmware, ID 7, Fast-40, LVD, parity checking
sym1: SCSI BUS has been reset.
scsi1 : sym-2.2.1
 target1:0:6: FAST-40 WIDE SCSI 80.0 MB/s ST (25 ns, offset 15)
  Vendor: IBM-PCCO  Model: ST118202LC    !#  Rev: B203
  Type:   Direct-Access                      ANSI SCSI revision: 02
 target1:0:6: tagged command queuing enabled, command queue depth 16.
 target1:0:6: Beginning Domain Validation
 target1:0:6: asynchronous.
WIDTH IS 1
 target1:0:6: wide asynchronous.
 target1:0:6: Domain Validation skipping write tests
 target1:0:6: FAST-40 WIDE SCSI 80.0 MB/s ST (25 ns, offset 15)
 target1:0:6: Ending Domain Validation
sym2: <896> rev 0x7 at pci 0000:04:04.0 irq 76
sym2: PA-RISC Firmware, ID 7, Fast-40, LVD, parity checking
sym2: SCSI BUS has been reset.
scsi2 : sym-2.2.1
sym3: <896> rev 0x7 at pci 0000:04:04.1 irq 77
sym3: PA-RISC Firmware, ID 7, Fast-40, LVD, parity checking
sym3: SCSI BUS has been reset.
scsi3 : sym-2.2.1
Attached scsi generic sg0 at scsi1, channel 0, id 6, lun 0,  type 0
SCSI device sda: 35548320 512-byte hdwr sectors (18201 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 35548320 512-byte hdwr sectors (18201 MB)
SCSI device sda: drive cache: write back
 /dev/scsi/host1/bus0/target6/lun0: p1 p2 p3 < p5 p6 p7 p8 > p4
Attached scsi disk sda at scsi1, channel 0, id 6, lun 0
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Adding 967672k swap on /dev/sda2.  Priority:-1 extents:1
EXT3 FS on sda5, internal journal
Linux Tulip driver version 1.1.13 (December 15, 2004)
tulip0: no phy info, aborting mtable build
tulip0:  MII transceiver #1 config 1000 status 782d advertising 01e1.
eth0: Digital DS21142/DS21143 Tulip rev 65 at 80001000, 00:10:83:7B:22:96, IRQ 66.
tulip1:  EEPROM default media type Autosense.
tulip1:  Index #0 - Media MII (#11) described by a 21140 MII PHY (1) block.
tulip1:  MII transceiver #1 config 3100 status 7849 advertising 01e1.
eth1: Digital DS21140 Tulip rev 34 at 80013300, 00:10:83:F8:96:DA, IRQ 72.
tulip2:  EEPROM default media type Autosense.
tulip2:  Index #0 - Media MII (#11) described by a 21140 MII PHY (1) block.
tulip2:  MII transceiver #1 config 3100 status 7849 advertising 01e1.
eth2: Digital DS21140 Tulip rev 34 at 80013200, 00:10:83:F8:96:43, IRQ 73.
tulip3:  EEPROM default media type Autosense.
tulip3:  Index #0 - Media MII (#11) described by a 21140 MII PHY (1) block.
tulip3:  MII transceiver #1 config 3100 status 7849 advertising 01e1.
eth3: Digital DS21140 Tulip rev 34 at 80013100, 00:10:83:F8:96:93, IRQ 74.
tulip4:  EEPROM default media type Autosense.
tulip4:  Index #0 - Media MII (#11) described by a 21140 MII PHY (1) block.
tulip4:  MII transceiver #1 config 3100 status 7849 advertising 01e1.
eth4: Digital DS21140 Tulip rev 34 at 80013000, 00:10:83:F8:96:78, IRQ 75.
tulip5:  EEPROM default media type Autosense.
tulip5:  Index #0 - Media MII (#11) described by a 21142 MII PHY (3) block.
tulip5:  MII transceiver #0 config 1000 status 7809 advertising 01e1.
eth5: Digital DS21142/DS21143 Tulip rev 65 at 80024100, 00:30:6E:2D:77:56, IRQ 78.
tulip6:  EEPROM default media type Autosense.
tulip6:  Index #0 - Media MII (#11) described by a 21142 MII PHY (3) block.
tulip6:  MII transceiver #0 config 1000 status 7809 advertising 01e1.
eth6: Digital DS21142/DS21143 Tulip rev 65 at 80024000, 00:30:6E:2D:77:57, IRQ 79.
usbcore: registered new driver hub
ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd: block sizes: ed 64 td 64
ohci_hcd 0000:00:0e.2: National Semiconductor Corporation USB Controller
ohci_hcd 0000:00:0e.2: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:0e.2: irq 1, io mem 0xf4007000
ohci_hcd 0000:00:0e.2: Using NSC SuperIO setup
ohci_hcd 0000:00:0e.2: resetting from state 'reset', control = 0x110
ohci_hcd 0000:00:0e.2: OHCI controller state
ohci_hcd 0000:00:0e.2: OHCI 1.0, NO legacy support registers
ohci_hcd 0000:00:0e.2: control 0x083 HCFS=operational CBSR=3
ohci_hcd 0000:00:0e.2: cmdstatus 0x00000 SOC=0
ohci_hcd 0000:00:0e.2: intrstatus 0x00000040 RHSC
ohci_hcd 0000:00:0e.2: intrenable 0x8000001a MIE UE RD WDH
ohci_hcd 0000:00:0e.2: fminterval a7782edf
ohci_hcd 0000:00:0e.2: hcca frame #0000
ohci_hcd 0000:00:0e.2: roothub.a 00001003 POTPGT=0 NOCP NDP=3
ohci_hcd 0000:00:0e.2: roothub.b 000e0000 PPCM=000e DR=0000
ohci_hcd 0000:00:0e.2: roothub.status 00008000 DRWE
ohci_hcd 0000:00:0e.2: roothub.portstatus [0] 0x00000100 PPS
ohci_hcd 0000:00:0e.2: roothub.portstatus [1] 0x00000100 PPS
ohci_hcd 0000:00:0e.2: roothub.portstatus [2] 0x00000100 PPS
usb usb1: default language 0x0409
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: National Semiconductor Corporation USB Controller
usb usb1: Manufacturer: Linux 2.6.12-1-parisc-smp ohci_hcd
usb usb1: SerialNumber: 0000:00:0e.2
usb usb1: hotplug
usb usb1: adding 1-0:1.0 (config #1, interface 0)
usb 1-0:1.0: hotplug
hub 1-0:1.0: usb_probe_interface
hub 1-0:1.0: usb_probe_interface - got id
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 3 ports detected
hub 1-0:1.0: standalone hub
hub 1-0:1.0: ganged power switching
hub 1-0:1.0: no over-current protection
hub 1-0:1.0: power on to power good time: 0ms
hub 1-0:1.0: local power source is good
hub 1-0:1.0: enabling power on all ports
hub 1-0:1.0: state 5 ports 3 chg 0000 evt 0000
ohci_hcd 0000:00:0e.2: created debug files
ohci_hcd 0000:00:0e.2: GetStatus roothub.portstatus [0] = 0x00010301 CSC LSDA PPS CCS
hub 1-0:1.0: port 1, status 0301, change 0001, 1.5 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0e.2: GetStatus roothub.portstatus [0] = 0x00100303 PRSC LSDA PPS PES CCS
usb 1-1: new low speed USB device using ohci_hcd and address 2
ohci_hcd 0000:00:0e.2: GetStatus roothub.portstatus [0] = 0x00100303 PRSC LSDA PPS PES CCS
usb 1-1: skipped 1 descriptor after interface
usb 1-1: default language 0x0409
usb 1-1: new device strings: Mfr=1, Product=2, SerialNumber=0
usb 1-1: Product: N48
usb 1-1: Manufacturer: Logitech
usb 1-1: hotplug
usb 1-1: adding 1-1:1.0 (config #1, interface 0)
usb 1-1:1.0: hotplug
ohci_hcd 0000:00:0e.2: GetStatus roothub.portstatus [1] = 0x00010301 CSC LSDA PPS CCS
hub 1-0:1.0: port 2, status 0301, change 0001, 1.5 Mb/s
hub 1-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x301
ohci_hcd 0000:00:0e.2: GetStatus roothub.portstatus [1] = 0x00100303 PRSC LSDA PPS PES CCS
usb 1-2: new low speed USB device using ohci_hcd and address 3
ohci_hcd 0000:00:0e.2: GetStatus roothub.portstatus [1] = 0x00100303 PRSC LSDA PPS PES CCS
usb 1-2: skipped 1 descriptor after interface
usb 1-2: default language 0x0409
usb 1-2: new device strings: Mfr=1, Product=2, SerialNumber=0
usb 1-2: Product: Standard USB Keyboard 
usb 1-2: Manufacturer: Silitek
usb 1-2: hotplug
usb 1-2: adding 1-2:1.0 (config #1, interface 0)
usb 1-2:1.0: hotplug
hub 1-0:1.0: state 5 ports 3 chg 0000 evt 0004
usbkbd 1-2:1.0: usb_probe_interface
usbkbd 1-2:1.0: usb_probe_interface - got id
input: Silitek Standard USB Keyboard  on usb-0000:00:0e.2-2
usbcore: registered new driver usbkbd
drivers/usb/input/usbkbd.c: :USB HID Boot Protocol keyboard driver
usbmouse 1-1:1.0: usb_probe_interface
usbmouse 1-1:1.0: usb_probe_interface - got id
input: Logitech N48 on usb-0000:00:0e.2-1
usbcore: registered new driver usbmouse
drivers/usb/input/usbmouse.c: v1.6:USB HID Boot Protocol mouse driver
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda4, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
module reiserfs relocation of symbol strlen is out of range (0x3ffeffeb in 17 bits)
JFS: nTxBlock = 8192, nTxLock = 65536
eth0: Setting full-duplex based on MII#1 link partner capability of 45e1.
NET: Registered protocol family 10
Disabled Privacy Extensions on device 10417448(lo)
IPv6 over IPv4 tunneling driver
eth0: no IPv6 routers present



00000000-7fffffff : System RAM
  00000000-000009ff : PDC data (Page Zero)
  00100000-00397fff : Kernel code
  00398000-004e600b : Kernel data
f05d0000-f05d0000 : lcd_data
f05d0008-f05d0008 : lcd_cmd
f4000000-f47fffff : PCI00 LMMIO
  f4000000-f4001fff : sym53c8xx
  f4002000-f4003fff : sym53c8xx
  f4004000-f40043ff : sym53c8xx
  f4005000-f40053ff : sym53c8xx
  f4007000-f4007fff : ohci_hcd
  f4008000-f40083ff : tulip
f4800000-f4ffffff : PCI01 LMMIO
  f4900000-f490007f : tulip
  f4901000-f490107f : tulip
  f4902000-f490207f : tulip
  f4903000-f490307f : tulip
f5000000-f57fffff : PCI03 LMMIO
  f5000000-f5001fff : sym53c8xx
  f5002000-f5003fff : sym53c8xx
  f5004000-f50043ff : tulip
  f5005000-f50053ff : tulip
  f5006000-f50063ff : sym53c8xx
  f5007000-f50073ff : sym53c8xx
f6000000-f67fffff : PCI05 LMMIO
f7000000-f77fffff : PCI06 LMMIO
fa000000-fbffffff : PCI06 ELMMIO
  fa100000-fa4fffff : stifb mmio
  fb000000-fb257fff : stifb fb
fed00000-fed00fff : SBA
fed30000-fed30fff : LBA
fed32000-fed32fff : LBA
fed34000-fed34fff : LBA
fed38000-fed38fff : LBA
fed3c000-fed3cfff : LBA
fef00000-feffffff : Astro Intr Ack
fff80000-fffaffff : Central Bus
  fffa0000-fffa0fff : CPU
  fffa2000-fffa2fff : CPU
fffb0000-fffdffff : Local Broadcast
fffe0000-ffffffff : Global Broadcast



00000000-00001fff : PCI00 Ports
  00000020-0000003e : pic1
  000000a0-000000be : pic2
  000007e0-000007fe : acpi
  00000800-000008ff : sym53c8xx
  00000900-000009ff : sym53c8xx
  00001000-0000107f : tulip
00012000-00013fff : PCI01 Ports
  00013000-0001307f : tulip
  00013100-0001317f : tulip
  00013200-0001327f : tulip
  00013300-0001337f : tulip
00024000-00025fff : PCI03 Ports
  00024000-0002407f : tulip
  00024100-0002417f : tulip
  00024200-000242ff : sym53c8xx
  00024300-000243ff : sym53c8xx
00038000-00039fff : PCI05 Ports
0004c000-0004dfff : PCI06 Ports