Linux version 2.6.18-rc4-pa1 (varenet@magnum) (gcc version 4.1.2 20060708 (prerelease) (Debian 4.1.1-8)) #2 SMP Mon Aug 14 14:04:24 CEST 2006 FP[0] enabled: Rev 1 Model 20 The 64-bit Kernel has started... Initialized PDC Console for debugging. Determining PDC firmware type: 64 bit PAT. model 00008870 00000491 00000000 00000002 3e0505e7352af70f 100000f0 00000008 000000b2 000000b2 vers 00000301 CPUID vers 20 rev 4 (0x00000284) capabilities 0x35 model 9000/800/rp3440 parisc_cache_init: Only equivalent aliasing supported! Memory Ranges: 0) Start 0x0000000000000000 End 0x000000003fffffff Size 1024 MB 1) Start 0x0000004040000000 End 0x00000040ffdfffff Size 3070 MB Total Memory: 4094 MB SMP: bootstrap CPU ID is 0 Built 2 zonelists. Total pages: 1048064 Kernel command line: root=/dev/sda3 console=ttyS1 palo_kernel=1/vmlinux-pa8800-2PID hash table entries: 4096 (order: 12, 32768 bytes) start_kernel(): bug: interrupts were enabled early Console: colour dummy device 160x64 ------------------------ | Locking API testsuite: ---------------------------------------------------------------------------- | spin |wlock |rlock |mutex | wsem | rsem | -------------------------------------------------------------------------- A-A deadlock:failed|failed| ok |failed|failed|failed| A-B-B-A deadlock:failed|failed| ok |failed|failed|failed| A-B-B-C-C-A deadlock:failed|failed| ok |failed|failed|failed| A-B-C-A-B-C deadlock:failed|failed| ok |failed|failed|failed| A-B-B-C-C-D-D-A deadlock:failed|failed| ok |failed|failed|failed| A-B-C-D-B-D-D-A deadlock:failed|failed| ok |failed|failed|failed| A-B-C-D-B-C-D-A deadlock:failed|failed| ok |failed|failed|failed| double unlock: ok | ok |failed| ok |failed|failed| initialize held:failed|failed|failed|failed|failed|failed| bad unlock order: ok | ok | ok | ok | ok | ok | -------------------------------------------------------------------------- recursive read-lock: | ok | |failed| recursive read-lock #2: | ok | |failed| mixed read-write-lock: |failed| |failed| mixed write-read-lock: |failed| |failed| -------------------------------------------------------------------------- hard-irqs-on + irq-safe-A/12:failed|failed| ok | soft-irqs-on + irq-safe-A/12:failed|failed| ok | hard-irqs-on + irq-safe-A/21:failed|failed| ok | soft-irqs-on + irq-safe-A/21:failed|failed| ok | sirq-safe-A => hirqs-on/12:failed|failed| ok | sirq-safe-A => hirqs-on/21:failed|failed| ok | hard-safe-A + irqs-on/12:failed|failed| ok | soft-safe-A + irqs-on/12:failed|failed| ok | hard-safe-A + irqs-on/21:failed|failed| ok | soft-safe-A + irqs-on/21:failed|failed| ok | hard-safe-A + unsafe-B #1/123:failed|failed| ok | soft-safe-A + unsafe-B #1/123:failed|failed| ok | hard-safe-A + unsafe-B #1/132:failed|failed| ok | soft-safe-A + unsafe-B #1/132:failed|failed| ok | hard-safe-A + unsafe-B #1/213:failed|failed| ok | soft-safe-A + unsafe-B #1/213:failed|failed| ok | hard-safe-A + unsafe-B #1/231:failed|failed| ok | soft-safe-A + unsafe-B #1/231:failed|failed| ok | hard-safe-A + unsafe-B #1/312:failed|failed| ok | soft-safe-A + unsafe-B #1/312:failed|failed| ok | hard-safe-A + unsafe-B #1/321:failed|failed| ok | soft-safe-A + unsafe-B #1/321:failed|failed| ok | hard-safe-A + unsafe-B #2/123:failed|failed| ok | soft-safe-A + unsafe-B #2/123:failed|failed| ok | hard-safe-A + unsafe-B #2/132:failed|failed| ok | soft-safe-A + unsafe-B #2/132:failed|failed| ok | hard-safe-A + unsafe-B #2/213:failed|failed| ok | soft-safe-A + unsafe-B #2/213:failed|failed| ok | hard-safe-A + unsafe-B #2/231:failed|failed| ok | soft-safe-A + unsafe-B #2/231:failed|failed| ok | hard-safe-A + unsafe-B #2/312:failed|failed| ok | soft-safe-A + unsafe-B #2/312:failed|failed| ok | hard-safe-A + unsafe-B #2/321:failed|failed| ok | soft-safe-A + unsafe-B #2/321:failed|failed| ok | hard-irq lock-inversion/123:failed|failed| ok | soft-irq lock-inversion/123:failed|failed| ok | hard-irq lock-inversion/132:failed|failed| ok | soft-irq lock-inversion/132:failed|failed| ok | hard-irq lock-inversion/213:failed|failed| ok | soft-irq lock-inversion/213:failed|failed| ok | hard-irq lock-inversion/231:failed|failed| ok | soft-irq lock-inversion/231:failed|failed| ok | hard-irq lock-inversion/312:failed|failed| ok | soft-irq lock-inversion/312:failed|failed| ok | hard-irq lock-inversion/321:failed|failed| ok | soft-irq lock-inversion/321:failed|failed| ok | hard-irq read-recursion/123: ok | soft-irq read-recursion/123: ok | hard-irq read-recursion/132: ok | soft-irq read-recursion/132: ok | hard-irq read-recursion/213: ok | soft-irq read-recursion/213: ok | hard-irq read-recursion/231: ok | soft-irq read-recursion/231: ok | hard-irq read-recursion/312: ok | soft-irq read-recursion/312: ok | hard-irq read-recursion/321: ok | soft-irq read-recursion/321: ok | -------------------------------------------------------- 142 out of 218 testcases failed, as expected. | ---------------------------------------------------- Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes) Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes) Memory: 4192256k available Mount-cache hash table entries: 256 Brought up 1 CPUs migration_cost=0 NET: Registered protocol family 16 Searching for devices... Found devices: 1. Storm Peak Slow at 0xfffffffffe780000 [128] { 0, 0x0, 0x887, 0x00004 } 2. Storm Peak Slow at 0xfffffffffe781000 [129] { 0, 0x0, 0x887, 0x00004 } 3. Storm Peak Slow at 0xfffffffffe798000 [152] { 0, 0x0, 0x887, 0x00004 } 4. Storm Peak Slow at 0xfffffffffe799000 [153] { 0, 0x0, 0x887, 0x00004 } 5. Everest Mako Memory at 0xfffffffffed08000 [8] { 1, 0x0, 0x0af, 0x00009 } 6. Pluto BC McKinley Port at 0xfffffffffed00000 [0] { 12, 0x0, 0x880, 0x0000c } 7. Mercury PCI Bridge at 0xfffffffffed20000 [0/0] { 13, 0x0, 0x783, 0x0000a } 8. Mercury PCI Bridge at 0xfffffffffed22000 [0/1] { 13, 0x0, 0x783, 0x0000a } 9. Mercury PCI Bridge at 0xfffffffffed24000 [0/2] { 13, 0x0, 0x783, 0x0000a } 10. Mercury PCI Bridge at 0xfffffffffed26000 [0/3] { 13, 0x0, 0x783, 0x0000a } 11. Mercury PCI Bridge at 0xfffffffffed28000 [0/4] { 13, 0x0, 0x783, 0x0000a } 12. Mercury PCI Bridge at 0xfffffffffed2c000 [0/6] { 13, 0x0, 0x783, 0x0000a } 13. Mercury PCI Bridge at 0xfffffffffed2e000 [0/7] { 13, 0x0, 0x783, 0x0000a } 14. BMC IPMI Mgmt Ctlr at 0xfffffff0f05b0000 [16] { 15, 0x0, 0x004, 0x000c0 } Enabling PDC_PAT chassis codes support v0.05 Releasing cpu 1 now, hpa=fffffffffe781000 FP[1] enabled: Rev 1 Model 20 migration_cost=1000 Releasing cpu 2 now, hpa=fffffffffe798000 FP[2] enabled: Rev 1 Model 20 migration_cost=1000 Releasing cpu 3 now, hpa=fffffffffe799000 FP[3] enabled: Rev 1 Model 20 migration_cost=1000 CPU(s): 4 x PA8800 (Mako) at 799.999900 MHz Setting cache flush threshold to 5373840 (4 CPUs online) SBA found Pluto 2.3 at 0xfffffffffed00000 LBA version TR3.2 (0x32) found at 0xfffffffffed20000 LBA version TR3.2 (0x32) found at 0xfffffffffed22000 LBA version TR3.2 (0x32) found at 0xfffffffffed24000 LBA version TR3.2 (0x32) found at 0xfffffffffed26000 allocation failed: out of vmalloc space - use vmalloc= to increase size. LBA version TR3.2 (0x32) found at 0xfffffffffed28000 allocation failed: out of vmalloc space - use vmalloc= to increase size. LBA version TR3.2 (0x32) found at 0xfffffffffed2c000 allocation failed: out of vmalloc space - use vmalloc= to increase size. LBA version TR3.2 (0x32) found at 0xfffffffffed2e000 allocation failed: out of vmalloc space - use vmalloc= to increase size. LBA: Truncating lmmio_space [fffffffff0000000/fffffffffecffffe] to [fffffffff0000000,fffffffffe77ffff] SCSI subsystem initialized NET: Registered protocol family 2 IP route cache hash table entries: 131072 (order: 8, 1048576 bytes) TCP established hash table entries: 131072 (order: 10, 4194304 bytes) TCP bind hash table entries: 65536 (order: 9, 2097152 bytes) TCP: Hash tables configured (established 131072 bind 65536) TCP reno registered Chassis warnings not supported. unwind_init: start = 0x10477f00, end = 0x1049d7e0, entries = 9614 Performance monitoring counters enabled for Storm Peak Slow Initializing RT-Tester: OK SGI XFS with large block/inode numbers, no debug enabled io scheduler noop registered io scheduler anticipatory registered (default) io scheduler deadline registered io scheduler cfq registered PDC Stable Storage facility v0.30 Soft power switch support not available. Generic RTC Driver v1.07 Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing enabled 0000:e0:01.0: ttyS0 at MMIO 0xfffffffff4051000 (irq = 27) is a 16450 0000:e0:01.1: ttyS1 at MMIO 0xfffffffff4050000 (irq = 27) is a 16550A 0000:e0:01.1: ttyS2 at MMIO 0xfffffffff4050010 (irq = 27) is a 16550A 0000:e0:01.1: ttyS3 at MMIO 0xfffffffff4050038 (irq = 27) is a 16550A RAMDISK driver initialized: 16 RAM disks of 32768K size 1024 blocksize loop: loaded (max 8 devices) tg3.c:v3.64 (July 31, 2006) eth0: Tigon3 [partno(BCM95700A6) rev 0105 PHY(5701)] (PCI:66MHz:64-bit) 10/100/1000BaseT Ethernet 00:30:6e:4b:13:ad eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[1] TSOcap[0] eth0: dma_rwctrl[76ff2d0f] dma_mask[32-bit] sym0: <1010-66> rev 0x1 at pci 0000:20:01.0 irq 22 sym0: No NVRAM, ID 7, Fast-80, LVD, parity checking sym0: SCSI BUS has been reset. scsi0 : sym-2.2.3 Vendor: HP 73.4G Model: ST373453LC Rev: HPC3 Type: Direct-Access ANSI SCSI revision: 03 target0:0:0: tagged command queuing enabled, command queue depth 16. target0:0:0: Beginning Domain Validation target0:0:0: asynchronous target0:0:0: wide asynchronous target0:0:0: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 31) target0:0:0: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 31) target0:0:0: Ending Domain Validation Vendor: HP 73.4G Model: ST373453LC Rev: HPC3 Type: Direct-Access ANSI SCSI revision: 03 target0:0:1: tagged command queuing enabled, command queue depth 16. target0:0:1: Beginning Domain Validation target0:0:1: asynchronous target0:0:1: wide asynchronous target0:0:1: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 31) target0:0:1: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 31) target0:0:1: Ending Domain Validation sym1: <1010-66> rev 0x1 at pci 0000:20:01.1 irq 23 sym1: No NVRAM, ID 7, Fast-80, LVD, parity checking sym1: SCSI BUS has been reset. scsi1 : sym-2.2.3 Vendor: SEAGATE Model: ST318203LC Rev: HP04 Type: Direct-Access ANSI SCSI revision: 02 target1:0:2: tagged command queuing enabled, command queue depth 16. target1:0:2: Beginning Domain Validation target1:0:2: asynchronous target1:0:2: wide asynchronous target1:0:2: FAST-40 WIDE SCSI 80.0 MB/s ST (25 ns, offset 15) target1:0:2: Domain Validation skipping write tests target1:0:2: Ending Domain Validation SCSI device sda: 143374738 512-byte hdwr sectors (73408 MB) sda: Write Protect is off SCSI device sda: drive cache: write through w/ FUA SCSI device sda: 143374738 512-byte hdwr sectors (73408 MB) sda: Write Protect is off SCSI device sda: drive cache: write through w/ FUA sda: sda1 sda2 sda3 sda4 sd 0:0:0:0: Attached scsi disk sda SCSI device sdb: 143374738 512-byte hdwr sectors (73408 MB) sdb: Write Protect is off SCSI device sdb: drive cache: write back w/ FUA SCSI device sdb: 143374738 512-byte hdwr sectors (73408 MB) sdb: Write Protect is off SCSI device sdb: drive cache: write back w/ FUA sdb: sdb1 sdb2 sdb3 sd 0:0:1:0: Attached scsi disk sdb SCSI device sdc: 35566480 512-byte hdwr sectors (18210 MB) sdc: Write Protect is off SCSI device sdc: drive cache: write back w/ FUA SCSI device sdc: 35566480 512-byte hdwr sectors (18210 MB) sdc: Write Protect is off SCSI device sdc: drive cache: write back w/ FUA sdc: unknown partition table sd 1:0:2:0: Attached scsi disk sdc mice: PS/2 mouse device common for all mice TCP bic registered NET: Registered protocol family 1 NET: Registered protocol family 17 kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem) readonly. Freeing unused kernel memory: BUG: warning at arch/parisc/kernel/smp.c:347/smp_call_function() Backtrace: [<0000000010113510>] dump_stack+0x18/0x28 [<000000001011e758>] smp_call_function+0x3e0/0x3e8 [<000000001014b1a0>] on_each_cpu+0x28/0x68 [<0000000010112b98>] flush_data_cache+0x28/0x38 [<0000000010111514>] free_initmem+0x8c/0x348 [<0000000010110140>] init+0x378/0x5a0 [<000000001010347c>] ret_from_kernel_thread+0x24/0x40 272k freed Write protecting the kernel read-only data: 202k INIT: version 2.86 booting * Files under mount point '/dev/shm' will be hidden. Will now activate swap. swapon on /dev/sda2 Adding 2000084k swap on /dev/sda2. Priority:-1 extents:1 across:2000084k Done activating swap. Will now check root file system. fsck 1.39 (29-May-2006) [/sbin/fsck.ext3 (1) -- /] fsck.ext3 -a -C0 /dev/sda3 /dev/sda3: clean, 16033/2198880 files, 182259/4393777 blocks Done checking root file system. A log will be saved in /var/log/fsck/checkroot if that location is writable. EXT3 FS on sda3, internal journal Setting the system clock.. Cannot access the Hardware Clock via any known method. Use the --debug option to see the details of our search for an access method. Cannot access the Hardware Clock via any known method. Use the --debug option to see the details of our search for an access method. System Clock set. Local time: Mon Aug 14 14:36:21 UTC 2006. Cleaning up ifupdown...done. Setting the system clock again.. Cannot access the Hardware Clock via any known method. Use the --debug option to see the details of our search for an access method. System Clock set. Local time: Mon Aug 14 14:36:22 UTC 2006. Loading device-mapper support. Will now check all file systems. fsck 1.39 (29-May-2006) Checking all file systems. [/sbin/fsck.xfs (1) -- /home] fsck.xfs -a /dev/sda4 /sbin/fsck.xfs: XFS file system. Done checking file systems. A log is being saved in /var/log/fsck/checkfs if that location is writable. Start setting kernel variables via /proc... Done setting kernel variables via /proc. Will now mount local filesystems. kjournald starting. Commit interval 5 seconds EXT3 FS on sda1, internal journal EXT3-fs: mounted filesystem with ordered data mode. /dev/sda1 on /boot type ext3 (rw) XFS mounting filesystem sda4 /dev/sda4 on /home type xfs (rw) Done mounting local filesystems. Will now activate swapfile swap. Done activating swapfile swap. Cleaning /tmp...done. Cleaning /var/run...done. Cleaning /var/lock...done. Setting up networking...done. Setting hostname to 'magnum'...done. Configuring network interfaces...tg3: eth0: Link is up at 100 Mbps, full duplex.tg3: eth0: Flow control is off for TX and off for RX. done. Initializing random number generator...done. Recovering nvi editor sessions...none found. INIT: Entering runlevel: 2 Starting system log daemon: syslogd. Starting kernel log daemon: klogd. Starting Name Service Cache Daemon: nscd. Starting internet superserver: inetd. Starting Postfix Mail Transport Agent: postfix. Starting OpenBSD Secure Shell server: sshd. Starting NTP server: ntpd. Starting periodic command scheduler.... Debian GNU/Linux testing/unstable magnum ttyS1 magnum login: